Hydraulic Cylinders

Mounting Heights for Stroke End Detection 20 & 25 Proper auto switch mounting positions (mm) B D-F9 D-F9V D-F9W D-F9WV D-A9 D-A9V D-A9 D-F9 D-F9W D-F9BAL Bore size (mm) SMC D-A90 B 15 16 A 12 13 B 19 20 A 11 12 B 18 19 A 8 9 SMC D-A90 20 25 A Approx.

Tie-rod Type Low Pressure Hydraulic Cylinder Double Acting/Double Rod Series CHAW

MA a A MA a Air release R (max.)

Modular Type Air Filter Series AF

Note 5) Without a valve function.

VDW30/40-XF

In general, a mesh of about 50 to 100 is a guideline for the filter. When using ordinary tap water, scaling and sludge from substances in hard water such as calcium and magnesium can cause solenoid valves to malfunction. It is therefore necessary to install a water softener to remove such substances and a filter (strainer) immediately before the solenoid valve.

Clean One-touch Fittings and Tubing Series KP/KPQ/KPG

Specifications Grade 1 Note 1) Particulate generation grade Air, Nitrogen gas, Water (pure water) Note 2) Fluid 1MPa Note 3) Maximum operating pressure (20C) 100kPa Operating vacuum pressure Caution 3MPa Proof pressure (20C) 20C to 80C Ambient and fluid temperature Series KP is a line of special One-touch fittings for use in clean room blowing and washing lines.

Compact Hydraulic Cylinder Double Acting/Single Rod Series CH
QB ø 20, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100

U A B B A D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U SMC SMC Approx. U B A B A Approx. U D-A73C D-A80C D-J79C D-A7*C,D-A80C Approx. U Approx. U D-A7*C,D-A80C A B A B Approx.

Compact Hydraulic Cylinder Series CH
KGB

and Mounting Heights for Stroke End Detection 20 & 25 Proper auto switch mounting positions (mm) B D-F9 D-F9V D-F9W D-F9WV D-A9 D-A9V D-A9 D-F9 D-F9W D-F9BAL Bore size (mm) SMC D-A90 B 11 12 A 16 17 B 15 16 A 15 16 B 14 15 A 12 13 SMC D-A90 20 25 A Approx.

Round Type Low Pressure Hydraulic Cylinder Series CH
M

HS Auto switch 36 12 24.5 SMC SMC A 33 B Auto switch 49.5 A B G 1/2 (applicable cable O.D. 6.8 to 11.5) Proper auto switch mounting positions (mm) D-H7 D-H7C D-H7W D-H7BAL D-C7 D-C8 D-C73C D-C80C D-G39 D-K39 D-A33, D-A34 D-A44 D-B5 D-B6 D-G5NTL D-H7F D-B59W Bore size (mm) A A B A A A A B A B B B B B 20 14 10 8.5 12 10.5 14 9 15 13 12 6.5 8.5 12 7 25 14.5 12.5 9.5 9 11 14.5 9.5 12.5 15.5 11.5

IR1000/2000/3000

If a directional switching valve (solenoid valve, mechanical valve, etc.) is mounted on the supply side of the regulator and repeatedly switched ON and OFF, wear of the nozzle/flapper section will be accelerated and a discrepancy in the setting value may occur. Therefore, avoid using a directional switching valve on the supply side.

Compact Hydraulic Cylinder Double Acting/Double Rod Series CH
QWB ø 20, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100

U B A Approx. U A B D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U Approx. U Approx. U SMC SMC Approx. U A B B A Approx. U D-A73C D-A80C D-J79C B A A B Approx.

Guide Cylinder Series MGG

6 A @0 @1 !9 #2 !0 #1 A' For ball bushing #5 @5 #0 @8 !7 @6 !3 #8 !2 @1 !0 @9 For slide bearing y For long stroke For 100 @7 For 80, 100 View A-A' Parts list Parts list No. Description No.

VNB

F A F u Pilot solenoid valve SF4--23 (Refer to the table below.)

Paddle Style Flow Switch Series IF3 For details about certified products conforming to international standards, visit us at www.smcworld.com. 1

(Equivalent to IP42) Dripproof/Rainproof type (JIS C 0920) 80C 58C (60C) or less Sealed construction. When using in a bad environment, such as outdoors, or areas exposed to water stream temporarily, or near the coast.

ISE70/75/75H

DOWN OUT1 U P SET ZS-31-A Bracket Note: Mounting screws are not included.

Low Maintenance Filter Series FN1

Contact P/A regarding the valves 3 to 5.

Line Filter Rated Pressure: 3.5, 7, 14, 21 MPa FH34/44/54/64 Series

Reliable outlet side A firm seal is secured through a special configuration combining a pressure clamp from an O-ring around the inner perimeter of the case with support from the cover, and there is no resistance when the cover is installed and removed. Large drain exhaust port The large M24 drain exhaust port assures rapid drainage.

Suction Guard (Produced upon receipt of order) FHG Series

Compact tank equipment The lubrication port strainer, suction filter, and air breather are all integrated into a single unit, reducing the volume of equipment around the tank. Selection of connection methods and accessories for a variety of applications Six methods are available as standard.

Suction Filter with Case FH99 Series

: Vertical upward When a value has been displayed, it will be automatically reset when the pump is stopped.

Hydraulic Filters

If any scratches or damage are found on the O-ring during assembly/disassembly, replace with a new O-ring. When washing the element, do not wipe it using a stiff brush or rag.

Oil Filter FH150 Series

Use a commercially available hook wrench (applicable sizes 80 to 85 mm) for tightening and removing clamping rings.