Prevents Micro-Bubbles As a guide, refer to the proper tightening torques shown below. 4 Note) Refer to page 17-5-35 for information on changing tubing sizes.
Option Symbol and Configuration Fluid and Options Option symbol Seal material Coil insulation Body, Shading coil material Option symbol and body material Brass SUS304 F L X F, B L, J B J B J J T A H A H A H D N G, J S Q E P V M Y A H K K A H A H B J V M V M Y D, E N, P B J Fluid(Application) Standard A B C D E F NBR FPM Argon Argon(long life) Ethyl Alcohol Ethylene glycol Ozone(low
Through the concurrent use of a CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
Use caution, as there is a danger of being burnt if a valve is touched directly. Fluid Quality Warning 1.
Pressure (including vacuum) holding It is not usable for an application such as holding the pressure (including vacuum) inside of a pressure vessel because air leakage is entailed in a valve. 8. When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit, etc. 9.
The above processes 1) and 2) are repeated at high speeds to establish the port A pressure. Circuit diagram The VY1D00, which is the smallest direct drive, consists of a solenoid, pressure sensor, control circuit, body cover, and a sub plate. The style with a sub plate can be used alone, and the style without a sub plate can also be used as a pilot valve.
Regenerative absorption units and regenerative resistors are available as options, therefore, separately order a model compatible with the motor and driver selection from the options ordering procedures on page 100. 400 L1 (mm) a = 1000 Pitching Yawing Vertical Vertical m a a = 2000 a = 3000 200 L1 Mep 0 5 10 15 Transfer load m (kg) 600 a = 1000 400 L3 (mm) a = 3000 a = 2000 a 200 L3 Mey
As a result, the tensile compression force of the floating joint may exceed its maximum level.
This option is supplied with the IDF370D as a standard accessory.
59 67 81 84 L 52.5 59 67 81 84 LD LU 13 14 17 23 23 ZZ 116 127 138 171 175 LA 35 41 46 62 62 ZZ Model MUl25 MUl32 MUl40 MUl50 MUl63 lLC 18 22 26 32 32 8 10 10 14 14 9 11 13 16 16 8 10 10 14 14 9 11 13 16 16 CD-MU02 +0.2 +0.4 +0.2 +0.4 +0.2 +0.4 +0.2 +0.4 +0.2 +0.4 Dimensions L, Z, and ZZ are reference dimensions for installing a single knuckle joint, which may be used as a guide.
Dimensions L, Z, and ZZ are reference dimensions for installing a double knuckle joint, which may be used as a guide.
Dimensions L, Z, and ZZ are reference dimensions for installing a double knuckle joint, which may be used as a guide.
a holding function for the unlocked state is not available for sizes 40 through 100, they can be used as shipped.
When a type 23 manifold base is added, tension bolts as well as a manifold block assembly is required. Order the tension bolt for the stations after the stations are increased (decreased), since the length of a tension bolt depends on the number of stations.
Model no. 1 3 5 A VZ X1 ( ) VZ3 A ( ) Manual override Entry is the same as standard products. Entry is the same as standard products.
Non-standard strokes for a size 6 cylinder are available as a special order.
The maximum dimension L1 is, as a rule, twice the thread size. (Example) For M3: L1 = 6 mm Applicable shaft types: X, Z The maximum dimension L2 is, as a rule, twice the thread size.
The maximum dimension L1 is, as a rule, twice the thread size.