REA/REB The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
This may cause unevenness in the mounting surface, play in the guide or an increase in the sliding resistance. 5. Do not apply strong impact or an excessive moment while mounting a workpiece. Otherwise, lubrication can run out. If an external force over the allowable moment is applied, it may cause play in the guide or an increase in the sliding resistance.
Never use in an atmosphere of explosive gases. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside actuators will become demagnetized. 3.
Fit an auto switch into the auto switch mounting groove to set it roughly to the mounting position for an auto switch. 4. After confirming the detecting position, tighten up the mounting screw (M2.5) attached to an auto switch, and secure the auto switch. 5. When changing the detecting position, carry out in the state of 3.
Note 1) This cylinder cannot perform an intermediate stop using an air pressure circuit in vertical operation. In this case, an intermediate stop can be performed only by using an external stopper, etc. Made-to-order products should be considered, too, depending on an operating environment, etc.
Hex. across flats may be deformed, if using an improper wrench for hex. across flats.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
Note 1) Values indicated by an asterisk () are optional.
Keep the air flow within the rated flow to prevent an outflow of lubricant to the outlet side.
How to Order Type 46 (5 port / Base mounted) Applicable solenoid valve 10-SYJ34310--SS5YJ3-46-05 -M5 Type 46 Type S46 Applicable blanking plate assembly SYJ3000-21-2A ( ) Single solenoid coil is located on the same side of A and B ports.
Size Nil 1 Without an insert bush With an insert bush Symbol Size 1 2 3 4 5 6 1 2 3 4 5 6 Used to block fittings which are not being used.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of overrun when an intermediate stop is performed.
How to Order Type 46 (5 port/Base mounted) 10 SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid pilot valve is on same side as the A, B port. Clean series CE-compliant M5 x 0.8 R1, R2 port Stations Nil 02 2 stations Valve mounting direction P port thread type Q CE-compliant : : Single solenoid pilot valve is on opposite side as the A, B port.
silicone rubber Symbol Pad diameter 2 4 5 6 40 46 N S U F GN GS 02 04 05 06 40 46 Pad type Type Bellows Symbol ZJ Dimensions: Pad Unit ZP2-02ZJ ZP2-04ZJ ZP2-05ZJ ZP2-06ZJ 8 6.2 6.4 4 4 4.3 2.2 2 3.8 5.7 1 2.5 1 4.5 8 8 2.3 2 6.4 4.7 4.6 1.5 3.3 1 2.6 6 4 2 5 6.7 5.7 4.3 2.5 8 6.4 3.8 ZP2-40ZJ ZP2-46ZJ 24 30 21 27 44 44 40.2 40.2 35 29 46 40 50 44 16 Symbol/Type Oval Pad W: Oval Pad size
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of overrun when an intermediate stop is performed.
Due to the nature of the lock-up mechanism, there is an axial play of about 0.5 to 1.0mm.