SMC Corporation of America
Elite Part Number Search
Search Results "PF3W720S-F04-AT-MR"

Before using the precision regulator, be sure to install the pressure gauge at the gauge port of the precision regulator. At this time, the recommended tightening torque of the pressure gauge is 7 to 9 Nm. 822 IR1000/2000/3000 Series Specific Product Precautions 2 Be sure to read this before handling the products.

Signal description Symbol Digital output power supply Failure Positioning complete Z phase pulse Interface power supply common Reverse pulse line Reverse pulse line Normal pulse line Normal pulse line 1 2 3 4 5 7 8 9 10 V+ ALM PF OP SG NP NG PP PG 11 12 13 14 15 16 17 19 20 Shield SD SG CR LSN LSP V5 SON OPC V24 Driver model MR-C10A MR-C20A MR-C10A1 MR-C20A1 Interface power supply common

F B With pressure at head side With pressure at rod side *Refer to p.5.3-2 for further information on the auto switch.

Plate cylinder with lock Traditional cylinder Plate Cylinder with Lock Series MLU Series MLU 25, 32, 40, 50 Drop prevention is possible at any point of stroke. Cylinder can be locked at any desired position. Drop prevention for middle stroke emergency stops Lock positions can be changed to accommodate the position of the external stopper and the thickness of the clamped work piece.

0.3m (2) (3) 750 Max. 1.0mgf/Nm3 ( 0.8ppm) Oil mist density on the secondary side Rated flow (l/min (ANR)) (4) 1500 3500 6000 1.8 2.8 3.5 6.7 Weight (kg) Note 1) Pressure for auto drain attached style should be set at 0.1MPa or higher.

The screw on the topmost section is a zero point adjustment screw which is locked at the factory and requires no adjustment for operation. 1. Do not use a precision regulator outside the range of its specifications as this can cause failure. (Refer to specifications.) 2.

Add the symbol at the beginning of part numbers for electro-pneumatic regulators, etc. to be mounted on the base. Note 1) Electro-pneumatic regulators are counted starting from station 1 on the left side with the OUT ports in front. Note 2) The port size for mounted electro-pneumatic regulators is Rc(PT)1/4 only.

To connect the IN side, hold the valve guide at its wrench flats (opposite side 10) and tighten it at the recommended torque of 1.5 to 2 Nm. Excessive torque or holding it at an area other than the specified portion may result in a malfunction. 2.

10mA of load current Internal Circuit ( ): If not applicable for IEC Standard 1mA at 100 V DC 100A at 24V DC Current leakage 0.8mA at 24V DC 1.5mA at 200V DC D-F59 Indicator light ON: When red light emitting diode Lead wire Oilproof vinyl heavy insulation cable, 4, 0.3mm2, 3 cores (Brown, Black, Blue), 2 cores (Brown, Blue), 0.5m Note 1) Refer to common specifications on the p.5.3-5.

mr Standard photo micro sensor for origin point SVDC to 24VDC -109o, Ripple(p-p) 1oe. or less SVDC to 24VDC, Load cufient('lc) 100mA, Residual voltage 0.8v or less sVDC to 24VDC, Load current{1c) 40mA, Rosidualvohage 0.4V or less -25 to +55"C (At holding: -30 to Operation: 5lo 85%RH (At holding: 5 to Terminal Brown o L' Black OUTPUT Blue DND(ov) O 'ON while lighl is shaded. ll "L' terminal

a load current of 10mA) 4V or less 0.8V or less Internal voltage drop Leakage current 100A or less at 24VDC 0.8mA or less at 24VDC Operating position .

mr Standard photo micro sensor for origin point SVDC to 24VDC -109o, Ripple(p-p) 1oe. or less SVDC to 24VDC, Load cufient('lc) 100mA, Residual voltage 0.8v or less sVDC to 24VDC, Load current{1c) 40mA, Rosidualvohage 0.4V or less -25 to +55"C (At holding: -30 to Operation: 5lo 85%RH (At holding: 5 to Terminal Brown o L' Black OUTPUT Blue DND(ov) O 'ON while lighl is shaded. ll "L' terminal

Confirm that the green LED is on when stopped at the established position.

Mount a switch at the center of the operating range. Adjust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting position shown in a catalog indicates the optimum position at stroke end.)

(at 20C) Data 10-12-9 9 Series CEP1 Proper Auto Switch Mounting Position Weight (Without mounting bracket/connector) (kg) Regarding dimensions for the proper auto switch mounting position (at stroke end), refer to page 1012-16.

Mp MHS Fv L MHC MHT MHY L: Distance to the point at which the load is applied (mm) Maximum allowable moment MHW Allowable vertical load Fv (N) Model Pitch moment: Mp (Nm) Yaw moment: My (Nm) Roll moment: Mr (Nm) MRHQ MHZ2-6 0.08 0.04 0.04 10 Misc.

Mp MHS Fv L MHC MHT MHY L: Distance to the point at which the load is applied (mm) Maximum allowable moment MHW Allowable vertical load Fv (N) Model Pitch moment: Mp (Nm) Yaw moment: My (Nm) Roll moment: Mr (Nm) MRHQ MHZ2-6 0.08 0.04 0.04 10 Misc.

(at 20C) Data 10-12-9 9 Series CEP1 Proper Auto Switch Mounting Position Weight (Without mounting bracket/connector) (kg) Regarding dimensions for the proper auto switch mounting position (at stroke end), refer to page 1012-16.

D-X 657 CE1 Series Auto Switch Proper Mounting Position Weight (Sensor cable length 0.5 m, With connector, Without mounting bracket (both ends tapped)) (kg) Regarding dimensions for the auto switch proper mounting position (at stroke end), refer to page 665.