ISG Contacts/Bulb gland Pressure Source Nil W Nil B C 1a1b (Standard) 2ab Contact Warning Enclosure Type A 20a (Standard) Type A 20b Type A 20c Bulb gland 1.
Note) The values are for an ambient temperature of 20C and at the of rated voltage. How to order solenoid coil assembly Name plate part no. Clip 1 1 G N VX02 AZ-T-VX Valve model Enter by referring to How to Order (Single Unit). Name plate Series Valve/Material 1 2 3 VX21 VX22 VX23 Symbol Valve N.C. N.O. Solenoid coil Nil 2 Clip part no. (For N.C.)
pilot exhaust, Common exhaust (pilot and main valve) 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) Lubrication Mounting position Not required 3 position closed center 3 position closed center Free (B) 2 (A) 4 (B) 2 (A) 4 (5) Impact/Vibration resistance (m/s2 ) 150/30 Dust proof Protection structure 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) Note 4) According to dynamic performance test JIS B8375-1981 (Coil temperature 20C
Insulation resistance Mkm, 20C (68F) 5 or more 16 44 8 SMC Connector manufacturers Fujitsu Ltd. Japan Aviation Electronics Industry, Ltd. J. S. T. Manufacturing Co., Ltd.
Conductor resistance /km, 20C 65 or less Note) When using the negative COM specification, use valves for negative COM. Withstand pressure V, 1 minute, AC 1000 Special wiring specifications (options) Insulation resistance M/km, 20C 5 or more Note) The minimum bending radius for D-sub connector cables is 20mm. (For 25P) Mixed single and double wiring are available as options.
Flow rate conversion Normal condition: 0C, 101.3 kPa, dry air Standard condition: 20C, 101.3 kPa, 65%RH (ANR) Switchable between these conditions.
Operating Pressure Specifications KA 3.0 Bend the tube into a U shape at a temperature of 20C. Fix one end and bend the loop gradually. Measure 2R when the tube breaks or is crushed.
The value of the minimum bending radius is measured at the temperature of 20C as shown in the figure on the right. Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually. Measure 2R when the tube breaks or is crushed. MS Fixed end KKA KP LQ MQR T T IDK 487
The value of the minimum bending radius is measured at the temperature of 20C as shown in the figure on the right. 4. Use inner sleeve, taking the removing force into consideration when used with One-touch fittings.
Silver (S1) MS Solid yellow (Y1) Clear yellow (Y2) KKA Neon yellow (Y3) KP Clear orange (YR1) Neon orange (YR2) LQ Nominal size (inch) 1 4 " 3 16" 1 8 " 3 8 " 1 2 " 5 32" 5 16" MQR Nominal size (mm) T T 3.2 IDK Fluid Air/Water 20C 0.8 Max. operating pressure (MPa) Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually.
(mm) ASG32F-01 4 ASG42F-02 6, 8 ASG52F-03 6 ASG62F-04 Sealant: Special FKM Seat ring: Stainless steel 303 8 12 4, 6 8, 10 10, 12 460 920 790 1580 100 180 230 390 Flow rate (l/min (ANR)) Controlled (free) flow 7 14 12 24 1.5 2.7 3.5 6 Effective area (mm2) Applicable tubing materials Note) Flow rate is measured at 0.5 MPa and 20C.
(at 20C) Data 10-12-9 9 Series CEP1 Proper Auto Switch Mounting Position Weight (Without mounting bracket/connector) (kg) Regarding dimensions for the proper auto switch mounting position (at stroke end), refer to page 1012-16.
Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.
Subsonic flow : Flow greater than the critical pressure ratio Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
(Variation: 10%) *7 The value when there is an ambient temperature of 20C and when the rated voltage is applied. The value depends on the ambient environment.
At this time correction factor line becomes A . coefficient (1) To get correction factor of 1.35 use ambient temperature correction factor A at 20C. (2) (3) To get outlet air temperature divide 38.5C from (1) by 1.35 from (2).
Note 1) ANR indicates the flow rate converted to the value at 20C under the atmospheric pressure and the state of relative humidity 65%. Note 2) The accessories should be mounted by user.
(at 20C) Data 10-12-9 9 Series CEP1 Proper Auto Switch Mounting Position Weight (Without mounting bracket/connector) (kg) Regarding dimensions for the proper auto switch mounting position (at stroke end), refer to page 1012-16.