SY3000V-OMY0001 X 2 N.O. X 2 N.C.N.O. 1 2 2 SY7000 4 3 4 3 N.C. X 2 N.O. X 2 N.C. N.O.
6 t Zinc chromated w Electroless nickel plated Black zinc chromated Accessory Accessory IN 2 Series ARJ310 Dimensions ARJ310-01 ARJ310F-01 Approx. 31 Approx. 56 Approx. 56 Approx. 35 32 22 M12 x 1 Panel fitting dimensions 12.5/Panel thickness: 4 or less Approx. 27 19 2 2 -5.5 Approx. 57.2 8.5 Approx. 82.5 15 Applicable tube O.D. 4, 6, 5/32, 1/4 Port size Rc, NPT 1/8 2 2 1 1 Pressure gauge
(Use SMC's tube cutter TK-1, 2, 3, 5 or 6 for cutting. Do not use pinchers, nippers or scissors, etc.) The tubing might be cut diagonally or flattened, making installation impossible or causing problems such as disconnection and leakage. 6 - 2. Specific Product Precautions (3) (5) Fix the body with a tightening tool.
(Use SMC's tube cutter TK-1, 2, 3, 5 or 6 for cutting. Do not use pinchers, nippers or scissors, etc.) The tubing might be cut diagonally or flattened, making installation impossible or causing problems such as disconnection and leakage. (2) Insert the tube into the union nut with the union nut removed.
Use SMCs tube cutter TK-1, 2 or 3 for cutting. Do not cut the tube with pliers, nippers, scissors, etc. If the tube is cut by any tools other than a tube cutter, the cut surface of the tube will be slanted or flat, making it impossible to be connected securely, or causing the tube to come off or air leakage after the tube is connected.
Insertion of tube 1) Cut the tube perpendicularly, being careful not 1) Nylon tubing Within 0.1 mm 2) Soft nylon tubing Within 0.1 mm 3) Polyurethane tubing Within +0.15 mm, to damage the external surface. Use SMC's tube cuter TK-1, 2 or 3 for cutting. Do not cut the tube with pliers, nippers, scissors, etc.
When cutting the tube, use tube cutters TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc. If cutting is done with tools other than tube cutters, the tube may be cut diagonally or become flattened, etc. This can make a secure installation impossible, and cause problems such as the tube pulling out after installation or air leakage. Allow some extra length in the tube. 2.
Use an SMC tube cutter TK-1, 2, 3. Do not cut the tubing with pliers, nippers, scissors, etc., otherwise the tubing will be deformed and problems may result. (see Figure 2) Unitmm 2)The outside diameter of the polyurethane tubing Mounting pitch A Straight-line tubing Pipe length Nylon Soft nylon Polyurethane size swells when internal pressure is applied to it.
Refer to Figure 2 and 3. [Figure 3] [Figure 2] 1. Stop operation and reduce the filter's internal pressure to atmosphere. 2. Rotate the cover counterclockwise (O on the cover L marking). Refer to Figure 1. Case Element [Figure 1] Case Cover Cover 5. Adjust the protrusion on the cover and the slit on the case so that they match up, then push the cover into the end of the case.
-OMH0002 SY series M8 M8 IP65 KJ SY (PE, A, B ) (V100-49-1-) NECA4202 (IEC60947-5-2)FA M8 3PIN SY3000 1) 1) 1) 1) 10.5mm 10.5mm TK-1, 2, 3 (0.40.6Nm IP65 30N 2) IP65 (V100-49-11) 0.1mm 2) 0.1mm 3) +0.15mm -0.2mm SY3000 M2 0.16Nm SY5000 M3 0.8Nm SY7000 M4 1.4Nm SY9000 M3 0.8Nm 13 No.SY3000-OMH0002 SY series 1) P 2) P 3) (2 ) 1 0.5MP 4) 5) AB (P AB )0.25MPa (PB PA)(Cv ) 14
If using any other type, it may cause the air leakage or tube coming off. 1 2 3 2 1 4 107
, vacuum adsorption retention, vacuum generated air flow Application ejector system Application vacuum pump system Vacuum line 2 port valve Ejector Pressure line Pressure line Air suction filter Series ZFC 2 port valve 2 port valve Air suction filter Series ZFC Air suction filter Series ZFC Vacuum pressure switch Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080
Use a tube cutter TK-1, 2, or 3. Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
(Use tube cutter TK-1, 2 or 3. Do not cut the tube with cutting pliers, nippers, scissors, etc.) 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Then, pull it back gently to make sure that it does not come out.
Use a tube cutter TK-1, 2, or 3. Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
(Use tube cutter TK-1, 2 or 3. Do not cut the tube with cutting pliers, nippers, scissors, etc.) 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Then, pull it back gently to make sure that it does not come out.
CLIP FOR REEL, CONNECTORS, TK/TG TUBE TOOLS, 2X, TK/TG NO SIZE RATING, 4.07065 lb
REPLACEMENT BLADES, TK-5, TUBING ACCESSORIES TM, TK, TG, H33, 180 lb
Applicable bore (mm) Round type A D L N R W MM Flat type Applicable bore (mm) TDH10 TC TH TK TN TT TU TV TW TX TY TZ Part no. CJ-CF006 CJ-CR006 6 6 8 11 5 8 6 M3 x 0.5 10 CJ-T010B CJ-CF010 CJ-CR010 3.3 10 8 10 13 6 10 8 M4 x 0.7 29 18 2 9 40 22 32 12 8 4.5 3.1 +0.048 0 16 CJ-T016B CJ-CF016 CJ-CR016 5 16 10 12 15 7 12 10 M5 x 0.8 35 20 14 48 28 38 16 10 5.5 6.4 2.3 +0.048 0 6-3-11
Part Number Description: TUBE CUTTER Product Line: C Product Line Description: CONNECTORS Family Code: 731 Family Description: TK/TG TUBE TOOLS Class Code: 22 Part Code: 2 Reference Code: C PDF Documentation: Datasheet Click here to report information errorImage shown may not match exact part number