EX250-SPR_eng (Allowable SW power supply range: 19.2 V to 28.8 V) Fig. a Fig. b Summary of Product elements Double Single Double Double Double Single Double Double No. 0 2 4 6 Side A No. 5 Side A 0 2 3 5 Station Station 1 2 3 4 1 2 3 4 6 No. 1 3 5 7 Side B No. 1 4 6 Side B R O I PROCESS FIELD BUS F R P Voltage drop of max.1 V B U S PWR(V) RUN DIA BF H L H L ADDRESS + EX250 Free EX250 DIA BF PWR(V) RUN
Auto switch CUJ cylinder Cylinder B Cylinder A Auto switch Magnetic substance Non-magnetic spacer of 2.5 mm or more Without Shielding Plate d Bore (mm) 10 L 6 8 L d 19 6 19 6 19.5 6 The space can be reduced by attaching shielding plates (steel plates 0.2 to 0.3 mm thick) to the sides of the cylinders facing each other.
Fig. a Fig. b Double Single Double Double Double Single Double Double 1 No. 0 2 4 6 Side A No. 5 Side A 0 2 3 Input block SI unit Tie-rod (2 pcs.) accessory 3 4 Station Station 1 2 3 4 1 2 3 4 7 2 No. 1 3 5 7 Side B No. 1 4 6 Side B Bus cable and termination resistors The cables, connectors, and termination resistors used in CANopen networks shall meet the requirements defined in ISO 11898
Test range Thermometer Equipment for test Pressure tap Pressure tap Throttle valve in the upstream side Throttle valve in the downstream side Flow meter 2d 6d 20d 10d Fig. (3) Test circuit based on IEC60534-2-3, JIS B 2005 Front matter 6 Flow Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.
HRSH 090 6 Signal for the completion of preparation A signal is output when the circulating fluid temperature reaches the set temperature, when using contact input/output and serial communication. !0 !1 !2 !3 !4 !5 !6 HRSH HRSH No.
Adjuster foot Unfixed caster (Caster O.D.: 2.9 inch [75mm]) Fig. 2 Caster adjuster-foot bracket (2 pcs.) Fixing bolt (M8) 4.6 [118] A B Fig. 3 Fixing bolt (8 pcs.) Fig. 1 Mounting view 19 Optional Accessories Series HRS100/150 e Electric Conductivity Control Set The set indicates and controls the electric conductivity of the circulating uid. Refer to the Operation Manual for details.
HRSH 6 Signal for the completion of preparation A signal is output when the circulating fluid temperature reaches the set temperature, when using contact input/output and serial communication. !0 !1 !2 !3 !4 !5 !6 HRSE No.
I.D. 6 mm, the equivalent effective area at vertical axis can be found as approx. 18 mm 2.
The indicator light is lit when switch is off for D-P70 and D-P75. Thus, leak current is EXPECTED (D-P70 .. Max. 1 .8 mA, D-P75.. Max. 1.2 mA). This leak current could interfere the micro current control circuit.
The indicator light is lit when switch is off for D-P70 and D-P75. Thus, leak current is EXPECTED (D-P70 .. Max. 1 .8 mA, D-P75.. Max. 1.2 mA). This leak current could interfere the micro current control circuit.
ISA-2-7 ISAl-1 ISAl-2/ISAl-1 ISAl-3/ISAl-2 ISAl-4/ISAl-3 ISAl-5/ISAl-4 ISAl-6/ISAl-5 ISAl-6 No.
O ON-OFF output Refer to Technical Information on page 16-13-6. Switch output. Response time The inverse number of frequency response. The shorter the response time becomes, the higher the frequency becomes. Open collector Internally the output wire and terminal are directly connected to collector of output transistor. (Refer to Fig. (1) and (2).)
Fig. a Fig. b CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
6 #3 Magnet Return guide Resin Electroless nickel plated Rare earth !7 #4 Magnet holder End cap Resin Steel !8 #5 O-ring Stud Steel NBR Heat treatment !9 #6 Replacement Parts Contents Kit no. Bore size (mm) 6 MXY6-PS Set consists of 2 pieces of above 8 MXY8-PS !0, !
d A IZN10E-01 02m06 6 3.5 IZN10E-01 02m07 1/4" 7 34.7 26 2 x M3 x 0.5 thread depth 10 11 291 *1 Dimension of the resin part in described in the Mounting Warning note 3 (page 24). 18.31 One-touch fitting (Elbow) IZN10E-mm 16 17 D B C Applicable tubing O.D. d 180 [mm] Model d B C D IZN10E-mm16 6 22 16 11.5 IZN10E-mm17 1/4" 24.5 18.5 12 Female threads for piping (Rc1/8) IZN10E-11mm 14 Rc1/
INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ? 3-15 osi A used ptugged 1i2 Snlit t) 3-15 nsi rl plugged USEQ 1/2 Solil B Reverse _z 3-15 osi USEd plugged 1/2 Solil B 3-15 osi A plugged useo 1/2 Snlit D Fig.
INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ? 3-15 osi A used ptugged 1i2 Snlit t) 3-15 nsi rl plugged USEQ 1/2 Solil B Reverse _z 3-15 osi USEd plugged 1/2 Solil B 3-15 osi A plugged useo 1/2 Snlit D Fig.
Since the external slider and piston slider are directional for 6, 10 and holding type L, refer to the figures below when performing disassembly or maintenance. Put the external slider and piston slider together, and insert the piston slider into the cylinder tube so that they will have the correct positional relationship as shown in Fig. (2).
D-DN This catalog is printed on recycled paper with concern for the global environment.