CRB2/CRBU2/CRB1 Take measures to prevent freezing since moisture in circuits can freeze at, or below 5C, and this can cause damage to seals and lead to malfunctions. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Warning 1. Adjust the speed gradually increasing from a low speed to the desired setting.
Piston rod Table (2) MXP6 MXP10/12/16 L2 L2 L2 (mm) 10 (One side only) 10 (One side only) 9 8 8 8 8 8 Model MXP6-5C MXP6-10C MXP10-10C MXP10-20C MXP12-15C MXP12-25C MXP16-20C MXP16-30C Damage is not allowed. 3. Shock absorber is considered a consumable component. When energy absorption is decreased, replace it.
Take measures to prevent moisture from freezing in a piping circuit when using at 5C or less, since this may cause damage to the product and lead to malfunction.
1.41 0.41 1.07 0.46 1.32 0.52 1.33 0.51 1.71 0.28 0.82 0.34 1.07 0.23 0.81 0.19 0.49 335 LLB Series Specifications Model LLB3 LLB4 Clean Air Module Common Specifications Fluid Clean air, N2 gas (Inlet air conditions: equivalent to ISO 8573-1 and Quality Class 1.4.1-1.6.1) Note 3) Maximum operating pressure 0.7 MPa Set pressure 0.05 to 0.4 MPa Withstand pressure 1.0 MPa Fluid temperature 5C
./0.05 MPa Ambient and fluid temperature 5C to 60C Port size Rc1/4 (Gauge port Rc1/8) Weight Approx. 700 g (at 100 mm stroke) Construction/Principle of Operation When signal pressure enters input chamber q, the input diaphragm e is deflected left. Clearance of the nozzle y is reduced causing higher back pressure at diaphragm A u.
Water Physical property value Temperature Density [kg/L] Specific heat C [J/(kgK)] Conventional units Weight volume ratio [kgf/L] Specific heat C [cal/(kgfC)] 5C 1.00 4.2 x 103 1.00 1 x 103 10C 1.00 4.19 x 103 1.00 1 x 103 15C 1.00 4.19 x 103 1.00 1 x 103 20C 1.00 4.18 x 103 1.00 1 x 103 25C 1.00 4.18 x 103 1.00 1 x 103 30C 1.00 4.18 x 103 1.00 1 x 103 35C 0.99 4.18 x 103 0.99 1 x 103 40C
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. Operating Environment Warning (1) Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, steam, or where there is direct contact with any of these.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. 9 - Operating Environment 1. Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, steam, or Warning where there is direct contact with any of these.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. 9 - Operating Environment Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, steam, or Warning where there is direct contact with any of these.
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Piping Caution 1.
Take measures to prevent freezing when 5C or less, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Piping Caution 1. Preparation before piping Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil, and other debris from inside the pipe. 2.
Take measures to prevent freezing, since moisture in circuits may freeze at, or below 5C and this can cause damage to seals and lead to malfunctions. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. 1. When operating at high speed with a large load weight, a large amount of energy is applied to the actuator and can cause damage.
Take measures to prevent freezing, since moisture in circuits may be frozen under 5C, and this can cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Operating Environment Lubrication Warning Caution 1. Do not use in environments where there is a danger of corrosion. 1.
Take measures to prevent freezing when below 5C, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Refer to SMCs Air Preparation System catalog for further details on compressed air quality. Caution 1.
Take measures to prevent freezing when below 5C, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Refer to SMCs Best Pneumatics catalog Vol. 4 for further details on compressed air quality. Caution 1. Do not scratch or gouge the cylinder tube or the sliding parts of the piston rod by striking or grasping them with other objects.
Take measures to prevent freezing when below 5C, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Refer to SMCs Air Preparation System catalog for further details on compressed air quality. 1. Do not scratch or gouge the cylinder tube or the sliding parts of the piston rod by striking or grasping them with other objects.
Piping Caution Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. 1. Preparation before piping.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Best Pneumatics vol.4 catalog for further details on compressed air quality. Piping Caution 1.
Piping Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Best Pneumatics vol. 4 catalog for further details on compressed air quality. Caution 1.
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this can cause damage to seals and malfunction. Maintenance Warning 1. Perform maintenance according to the procedure indicated in the instruction manual. Improper handling can cause malfunction and damage of machinery or equipment. 2. Removal of equipment and supply/exhaust of compressed air.