Vane Type Rotary Actuator Series CRB1 New 63mm Bore Size .) + Switch unit Option With foot brackets (L) Mounting Auto switch units can be retrofitted even when equipped with foot brackets Dual Porting Options: Top or Side Locations Long side round/ Short side square J Positions can be freely selected based on the application. Top ports can be used even with auto switches.
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
L O L G H F K J E D I A B C 2-4.5 A B C D E F G H I J K L Model 4 ZFC100-04 6 ZFC100-06 53.2 9.1 30 14.1 10 18 11.6 19.5 23 20 29 5/32" ZFC101-03 1/4" ZFC101-07 6 ZFC200-06 8 ZFC200-08 67 15.5 34 17.5 14 22 15.6 23.1 27 24 35 1/4" ZFC201-07 5/16" ZFC201-09 Element Replacement Element replacement procedure 1) Stop operation and reduce the filter's internal pressure to atmosphere. 2) Turn cover
A type with a drain cock (manual discharge), with auto drain (automatic discharge), and a drain guide 1/4 female thread (option “J”) are available.
For the type with a drain cock (manual discharge), fittings and tubes can be piped to the M5 (female thread) on the end of the drain port.
1 Air Suction Filter In-line Type with One-touch Fittings Series ZFC Model ZX An in-line type air suction filter that prevents trouble in vacuum equipment due to contaminants in the air.
I Electro-pneumatic , / , ' ' Control signal t , / ' a Mist separator Controller Analog control tleHro-Pltsulnalic Regulalnn rTUz000/3 $rucilicflior$ Standard s . : j 1w301 Minimum supply pressure Set pressure + 0.1MPa Maximum supply pressure 0.2MPa 1.0MPa Regulating pressure rang 0 005 to 0.1 MPa 0.005 to 0.5MPa | 0.005 to 0.9MPa Voltage 24YDC !
1 and an exclusive grease pack. o Magnet CUJB8-S-PS 8 Steel Nickel plated !0 Rod end nut CUJB10-S-PS 10 NBR !1 Piston seal NBR !2 Rod seal NBR !
Failure to observe this procedure could lead to an excessive pressure drop. 758
P910 M ai nt enance and i nspect i on P10 SM C Corporat i on 4141, Sot okanda, Chi yodaku, Tokyo 1010021 J APAN Tel : +81 3 52078249 Fax: +81 3 52985362 U RL ht t p: //w w w . sm cw orl d. com 1 Saf et y I nst ruct i ons These saf et y i nst ruct i ons are i nt ended t o prevent hazardous si t uat i ons and/or equi pm ent dam age.
Excessive torque or holding it at an area other than the specified portion may result in a malfunction. 2. While piping to products or operating the handle, ensure that an excess bending moment should not be applied to a product, because it may result in damage.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
When optional parts are required separately, use the following part numbers to place an order. Part no. Option Note Part no.
Therefore, use the dryer in an area where the discharge will not be a problem. AT IDF IDU IDF FS Operation Caution IDFA Turn ON the power after the air dryer has been pressurized. If the power is turned ON before it is pressurized (particularly when the pressure is low), the check valve will not operate properly, possibly creating an abnormally large reactivated air flow rate.
Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators. 3.
5 10 Stroke absorption: (mm) 5 6 11 15 5.5 11 Collision speed: (m/s) 0.05 to 5 4.5 9 Max. operating frequency: (cycle/min) 80 70 45 25 Since the cylinder is in an intermediate stop condition when stroke adjustment is performed, use caution regarding the operating pressure and the kinetic energy of the load.
-X10 Ordering example) X10 X10 IZS 40 IZS 42 1660 1660 10 10 B B Bar length Type 41 42 520 700 760 880 940 1000 1060 1180 1240 1360 1420 1480 1540 1660 1720 1780 1840 1960 2020 2080 2140 2200 2260 2380 2440 Symbol Specifications Contents Model with electrode cartridge drop prevention cover The main unit is shipped fitted with an electrode cartridge drop prevention cover available as an option
Note 2) An element for the mist separator is included on the inlet side. Mineral grease is applied on the sliding parts inside the regulator. As such, improper use could cause run off of these lubricants to the outlet side. Please contact SMC if problems take place during operation.
When the fitting is removed from the tubing, the cfiuck and collet are rsloa8gd, lhus prsvnting thm from scraping and biting into the luba lo an unnessary degree. Aocopis tublng coniormlng to Doth sAEJSrt4 .nd F VSS106. Has high retaining lolce. Can b usd tor a wlde rang6 of pregaure from a low vacuum up to a pressure ol 150psl.