ZSE40/ISE40 ON YES Unit selection Hysteresis mode OFF P-1 P-2 High pressure (for positive pressure/compound pressure) High vacuum (for vacuum pressure) [P] ZSE ISE H H H (Fixed hysteresis) = 3 digits ON PSE Window comparator mode OFF NO P-1 P-2 High pressure (for positive pressure/compound pressure) High vacuum (for vacuum pressure) Z I SE3 Set the unit by either button or button. : kPa or MPa
A( ) A 24V 12V 100V SY100-82-3-05 SY100-82-3-06 SY100-82-2-01 24V DC 12V DC 100V AC SOL SOL C(+) C ZNR Light DIN connector circuit with light AC circuit DC circuit 1 2 1 2 NL R R LED NL: Neon light R: Resistor LED: Emitting diode R: Resistor 4.3-2 Series VQ20/30 Manifold Caution Caution Valve Mounting How to Mount/Remove from DIN Rail After confirming the gasket is correctly placed under
CS2 Panel mount type Embedded type i e u q r w t y Component Parts No.
:llv thn alphabtic:lly (Ex.: 27N.40(40/,m), 2N R Body g Port orl.d.--64, r NNFT Construction./Parts List Main Parts Parts List 1 1074-58 1 1 1 1r 1 636 NC4otr r 1185 l t l Series NAF Air Filter Float Type Flow Characteristics NAF5OOO N.O tvpe/ NAD44 With no pressure inside the bo!
Port size q Seal order no. r Seal order no. t Seal order no.
Rod Center Mounting Basic Fool ,r ' flange , trunn~~~ 1 !
/See 3.3.Step data setting on p.23 3.4.Parameter setting on P .29
P P P Lock position Z80 P P H R Rear lock Front lock Y59A Y69A P p P Manual release Y7PV Y7P P P p N L Non-locking type Locking type Y59B Y69B P p P Solid state switch Y7NW Y7NWV P P p Y7PW Y7PWV P P p Y7BW Y7BWV P P p Y7BA P p Lead wire symbols 0.5m . Nil (Example) Y69B 3m . L Y69BL 5m . Z Y69BZ Solid state switches marked with a "p" are produced upon receipt of order.
Internal circuit and wiring example Z/ISE40A(F)Output specification -S/-R (Analogue output mode) Switch output NPN open collector output type-2 output Max. 28 V, 80 mA Residual voltage 1 V or less R: Analogue output 1 to 5 V Output impedance 1 k S: Analogue output 4 to 20 mA Max. load impedance Power supply voltage 12 V: 300 Power supply voltage 24 V: 600 Min. load impedance 50 -S/-R (
Displays exact the same pressure values for all channels. kPa MPa Auto identification function (page 14) Can automatically identify the pressure range of a connected P/A sensor. CH kPa MPa kPa MPa MPa kPa kPa MPa kPa MPa OUT1 OUT2 CH 1 2 3 4 P R E S S U R E Copy function (page 14) Each channel's information can be copied to another channel.
With air cushion WB 2-P (Rc, NPT, G) WA GB Relief port M5 x 0.8 10 GA W W RA Relief port Width across flats B1 MM H1 D MAX.
(Refer to About TEMP READY function (P.527) for TEMP READY function.) Display [ ] if the circulating fluid discharge pressure has reached the pressure limit value. (Refer to About control function of circulating fluid discharge pressure (P.5-32) for details of PRESS LIMIT.) Ready / P.
P.5-12 (15) CH2 Independent pump operation CH2 pump operates independently while the button is pressed. P.5-12 To select a operation mode from the touch panel ( mode), contact input ( mode) (16) Operation mode P.5-12 Common or serial communication ( mode). (17) Operating condition display It indicates the run and stop status of the product. P.5-12 (18) Run/Stop To run/stop the product.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Request message
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.