Speed controller with one-touch fittings , Body sizes: M3, M5, 1/8, 1/4, 3/8, 1/2 , Maximum operating pressure 1MPa, Meter in or meter out control , Port sizes: M3, M5, U10/32, 01, 02, 03, 04 , Various tube O.D. in both metric and inch, FLOW CONTROL, AIRLINE EQUIPMENT, FLOW CONTROL W/FITTING, AB, AS***F M5 STANDARD (PT), .56830 lb
, FLOW CONTROLLER, S/STEEL, AIRLINE EQUIPMENT, ASG FLOW CONTROL S/STEEL, AB, ASG M5 STANDARD (PT), .06455 lb
, FLOW CONTROLLER, S/STEEL, AIRLINE EQUIPMENT, ASG FLOW CONTROL S/STEEL, AB, ASG M5 STANDARD (PT), .09997 lb
, FLOW CONTROLLER, S/STEEL, AIRLINE EQUIPMENT, ASG FLOW CONTROL S/STEEL, AB, ASG M5 STANDARD (PT), .05544 lb
, FLOW CONTROLLER, S/STEEL, AIRLINE EQUIPMENT, ASG FLOW CONTROL S/STEEL, AB, ASG M5 STANDARD (PT), .08148 lb
CUJ If this surface is to be used for mounting, a spacer composed of a non-magnetic substance (aluminum, etc.) is required as shown in the figure below.
(The diagram below is provided as a guide.)
Before Use Fieldbus system EX500-GEN2 Product Summary Mounting and Installation LED Display Installation System configuration Direct mounting Install the product using 4 M5 screws x 15 mm or longer with a head 5.2 minimum.
Note 3) The value at a temperature of 20C, with a 10% or less O.D. variable rate.
for attaching a limit switch Applicable product Kit no.
35) 10 (10) 16.5 19.2 18.4 21.6 20.5 23.2 22.4 25.6 05 20 10 A A 30 (25) 10 (10) 1 15 10 For D-F9, D-M9 Operating angle m: Value of the operating range Lm of a single auto switch converted to an axial rotating angle.
ad an an ju t r t r st en m en en stm m t r st ju ju an ad ad ge le e Ang 5 gl n A B port A port B port A port 90 A 5 n gl ge e an ad t r ju en st m 180 Note) The drawings show the rotation range for the shaft's single flat.
Use a spanner corresponding to the size of hexagonal portion, or hexagonal portion may become deformed. 3. Tightening the threaded portion of an M3, M5 or M6 fittings 1) M3 First, tighten it by hand, then give it an additional 1/4 turn with a wrench. 2) M5 and M6 First, tighten it by hand, then give it an additional 1/6 turn with a wrench. Mounting Caution 1.
Individual grounding should be provided close to the product with a short cable. 138 Seal cap (for M8 connector socket): 16 pcs. Seal cap (for M12 connector socket): 1 pc. Accessory Seal cap (for M12 connector socket): 17 pcs. EX500-DX B Install the product using 2 M5 screws x 20 mm minimum with a head 9 to 11.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
) N01 NPT1/8 (M5) A1 A C4H 4mm5/32 inch C6H 6mm A2 B NH7 1/4 inch N7H A3 C C4L 4mm5/32 inch C6L 6mm B N7L 1/4 inch D + N NPN1 P PNP1 A NPN2 B PNP2 C NPN1+ D NPN1+ E PNP1+ F PNP1+ 1 L (2 m) 1 (2 m 1 G 1 M SI2 P (psi)1 1NP3 4 1 2kPaMPa -8No.PS-OML0002CN-G / A ZS-38-A1 (M35 L 2 ) B ZS-38-A2 (M35 L 2 ) C ZS-38-A3 (M35 L 2 ) ZS-27-C (M38 L 2 ) + ZS-27-D (M38 L 2 ) ZS-38-3L 3
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
3-N 18 21,41SA SS5YJ7SY3000-37-81A-3-6 3 14 SY3000-37-81A-3-7 3 58 Ass'y Assy Assy SY3000-37-80A-5 A 18 21,32SA SS5YJ3SY3000-37-80A-2 B SY3000-37-80A-7 A 916 SY3000-37-80A-4 B SY3000-37-80A-5 A 18 SY3000-37-80A-2 B 20,40, 42,43SA SS5YJ5SY3000-37-80A-7 A 912 SY3000-37-80A-4 B SY3000-37-80A-9 A 1316 SY3000-37-80A-7 B SY3000-37-80A-7 A 18 SY3000-37-80A-3 B 21,41SA SS5YJ7SY3000
IDX-OM-W026-A / Series IDF22E-20(-A,C,K,L,M,R,T) IDF22E-30(-A,C,K,L,M,R,T) IDF37E-20(-A,C,K,L,M,R,T) IDF37E-30(-A,C,K,L,M,R,T) IDF55E-30(-A,C,L,M,R,T) IDF75E-30(-A,C,L,M,R,T) URLhttps://www.smcworld.com/ English instruction manual can be downloaded from our URLhttps://www.smcworld.com/ SMC ISO4414 *1) JIS B8370 *2 ) *1) ISO4414Pneumatic fluid power General rules and safety requirements