High Purity Fluoropolymer Fittings HYPER FITTING ® Series LQ1 1 J type J type fitting assembly procedure Pull out the lever pin q. Rotate the lever assembly w to align the holes on the lever assembly w and the base e. Insert the lever pin q into the holes to fix the lever assembly w. 1 !
59 59 60 P Port size Rc VXD2140 Q R a b c d e f M L K J H F E D C B A N 69 (76) 77 (84) 87 (97) Q N 61 69 79 Q N 61 (68) 69 (76) 79 (89) N 61 (68) 69 (76) 79 (89) Normally open Normally closed VXD2142 , 30 30 35 59 59 62 57 74 81 34 51 58 29 37 43 34 43 47 20 20 23 92 92 95 104 (116) 26 44 59 66 28 35 40 3 8 8 14 23 39 47 47 48 39 65 78 86 42 46 56 52 56 66 63 80 90 3 8 1 2 32.5 118 (136)
The SYJ Valve is an innovative combination of space efficiency and performance superiority which provides real value to the design solution. Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal
The SYJ Valve is an innovative combination of space efficiency and performance superiority which provides real value to the design solution. Whether designed in a manifold or used as a single valve, this small profile increases design flexibility and minimizes space requirements. The SYJ valve utilizes a low power (0.5 watts standard) pilot solenoid design, which dramatically reduces thermal
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone
Disassembly 1) After loosening the screw q, then if the housing r is pulled in the direction of the screw, the connector will be removed from the body of equipment (solenoid, etc.). 2) Pull out the screw q, then remove the gasket or . 3) On the bottom part of the terminal block e, theres a cut-off part (indication of an arrow) .
(Refer to q shown in the figure below.) If the lock plate is not locked completely, the pad may drop due to the vibration or load during operation. q ZA Holder y ZX Non-rotating hole Plate ZM 3. To ensure the safety, be sure to mount the lock screw on the lock plate before use. (Refer to w shown in the figure below.)
Nozzle 494 RoHS Desktop Duster Box ZVB Series IZS How to Order IZN A S B ZVB 20 IZF ZVB ZVB q w e r t IZD IZE Nil None Note 1) S With photoelectric sensor Note 2) r AC adapter q Size w Additional air blow B With additional air blow e Photoelectric sensor Note 1) It is necessary to connect an external switch to the external input terminal on the back side of the product.
Red flashes if the CPU is abnormal. q w e r t y u Green lights up when emitters require cleaning.
Port size q Seal order no. r Seal order no. t Seal order no.
q r r w w (y) e (y) t e t Component Parts No.
When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.
When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.
KT-FGDC KT-FGDE KT-FGDT KT-FGDF Replacement parts A 1 kit for each of each one of seals q to t and gasket.
Refer to page 41 for how to return to the locked state. 10 MWB Series Construction io w er uy q !3 !4 !2 !8!5!6 !0!1 !7 @1@0 @2 @6 @3 @5@8 @4@9 #5 #7 #9 #8#6#4 #0#1 $1 $0 t !9 #3 #2 @7 Component Parts Component Parts No. Description Material Qty.
AMl Related poroducts Maintenance Caution q The replacement interval for the element is when the pressure drop reaches 0.1MPa or after 2 years of operation, whichever comes first.
Chrome treatment (Epoxy coating on inner surface) Housing Body q w e Tempered glass Sight glass AMD850 is aluminum casting Replacement Parts AMD450 Part No. Description Material No.
AFF AMl Related poroducts Mounting Caution q Verify the direction of the flow of the compressed air and the e mark that indicates the inlet of the product before connecting.
ORIENTATION Caution on Design Caution q Design the layout so that the mist separator is installed in an area that is less susceptible to pulsations.
KT-FGDC KT-FGDE KT-FGDT KT-FGDF Replacement parts A 1 kit for each of each one of seals q to t and gasket.