Air Cylinder/Standard Type: Double Acting, Single Rod Series CG1 When re-tightening, tighten approximately 2 degrees more than the original position. 20 A
When re-tightening, tighten approximately 2 degrees more than the original position. 20 A
Do not over tighten the lock nut. 4.7-7 Series ML1 Basic Style Bottom side piping port size Mounting side should be processed according to the dimensions below.
40-140'F(5-m'c 2 -20 inch/sec {50 -500 mm/sec) 2 -30 jnch/sec (50-750 mm/sec) Not required (prelubricated at factory) Standard Stroke LLst Owhen mounting, completelyflush the piping and be careful that dust and chips do not erterthe cylinder. )Load of piston rod should always be aligned parallel with the cylinder axis.
CN2 11 15 14 2 12 PF SG CR PP PG NP NG SD V24 SON LSN LSP ALM SG 3 12 13 9 10 7 8 20 17 11 LG 19 P5 4 OP 1 V+ 20 12 7 6 P5 LG MR MRR MD MDR SD SG 7 8 1 2 4 5 9 P5 LG MR MRR MD MDR SHD 7 8 1 2 4 9 P5 LG MR MRR MD MDR SHD Note 3) Detector 17 16 Plate 5 Note 2) Note 6) Be sure to connect the shielding wires to the ground plate inside the connector.
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display.
Operating Pressure MPa How to Order 2 TH0425 TH0806/TH1075/TH1209 TH0604 Metric size TH0604 N 20 1 TH1008/TH1210 Length per roll Indication of tubing model Roll size 20m roll 100m roll Symbol 20 100 0.5 Color indication 0 -20 0 20 40 60 80 100120140160180200 Color Symbol N R BU B Translucent Red (Translucent) Blue (Translucent) Black (Opaque) Operating Temperature C Note) The maximum operating
Orifice size Electrical entry Orifice diameter 2mm 3mm 4mm 5mm 7mm Class 4 Class 3 Class 2 Symbol 2 3 4 5 7 Voltage G C T TL D DL DO Grommet Conduit Conduit terminal Conduit terminal with light DIN connector DIN connector with light 1 2 3 4 5 6 100VAC 200VAC 110VAC 220VAC 24VDC 12VDC For DIN connector (without connector) All are equipped with surge voltage suppressor.
Weight g (oz) Model IN side, OUT side ZFC100-04 4 10 (0.35) 11.5 (0.41) ZFC100-06 6 20 (0.70) Metric size ZFC200-06 6 30 (1.05) 21.5 (0.76) ZFC200-08 8 50 (1.75) ZFC101-03 5/32" 10 (0.35) 11.5 (0.41) ZFC101-07 1/4" 20 (0.70) Inch size ZFC201-07 1/4" 30 (1.05) 21.5 (0.76) ZFC201-09 5/16" 50 (1.75) Note 1) Flow rate when initial pressure drop is 0.003MPa (0.44psi) or less.
] 10 2250 lbf [10 KN] Relief port Nil No V Yes Stroke Sensor type Symbol Stroke (Applicable model) 12 12 mm (MACM2) 20 20 mm (MACM4) 30 30 mm (MACM6) 50 50 mm (MACM10) Nil Unsupported P Port side photo sensor mounted type B Port back side photo sensor mounted type Specications Precautions Model MACM2-12 MACM4-20 MACM6-30 MACM10-50 Max. allowable load weight lbf [KN] 450 [2] 900 [4] 1350 [
Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Specifications x100 IP address x 10 1 DIP SW Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Specifications Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Technical documentation giving detailed configuration information and the GSD file can be found on the SMC website (URL http://www.smcworld.com). Specifications Do not operate in an atmosphere containing flammable or explosive gases.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Connect valve manifold to the SI unit. Refer to the EX260 series valve manifold section in the valve catalogue for valve manifold dimensions. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the handle assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the handle assembly itself. Do not disassemble the parts that are not explained in this operation manual.
SET 20 VY1 + G P.SET PPA AL 14-11-19
Do not hurt the body seat during installation. Compression of the O-ring of the mating side of the body shall be 0.7 to 0.9mm.
Do not use moisture control tubing in applications where tubuing is required Min. bending radius mm(20) Tube dimensions operation manual at hand, and refer to it whenever a question or failure arises. Indoor (temperature of 40 oC, humidity of 75 %RH or less) Moisture Control Tube / IDK series Thank you for purchasing SMCs Moisture Control Tube.
Troubleshooting Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Manifolds SJ2000/3000, S0700 series : Refer to the catalogues and operation manuals for details on the solenoid valves and manifolds. How to mount the manifold 1.