Type of Connector: F (D-sub Connector 25 Pin), Connector Outlet Direction: 1 (Connector Top Direction), Stations: 6 Stations, SUP/EXH Block Mounting: D (D Side 2~10 Stations), Pilot: Internal Pilot, A, B Port: 02N (NPT1/4), Mounting Method: D (DIN Rail Mounting)
Type of Connector: F (D-sub Connector 25 Pin), Connector Outlet Direction: 1 (Connector Top Direction), Stations: 4 Stations, SUP/EXH Block Mounting: D (D Side 2~10 Stations), Pilot: Internal Pilot, A, B Port: N11 (3/8" One-touch Fitting), Mounting Method: D (DIN Rail Mounting)
Type of Connector: F (D-sub Connector 25 Pin), Connector Outlet Direction: 1 (Connector Top Direction), Stations: 4 Stations, SUP/EXH Block Mounting: D (D Side 2~10 Stations), Pilot: R (External Pilot), A, B Port: N11 (3/8" One-touch Fitting), Mounting Method: D (DIN Rail Mounting)
Type of Connector: F (D-sub Connector 25 Pin), Connector Outlet Direction: 1 (Connector Top Direction), Stations: 2 Stations, SUP/EXH Block Mounting: D (D Side 2~10 Stations), Pilot: Internal Pilot, A, B Port: C10 (ø10 One-touch Fitting), Mounting Method: D (DIN Rail Mounting)
3 Output specifications Symbol OUT1 OUT2 A NPN NPN B PNP PNP C NPN Analog (1 to 5 V) D NPN Analog (4 to 20 mA) E Note 2) PNP Analog (1 to 5 V) F Note 2) PNP Analog (4 to 20 mA) G Note 2) NPN External input Note 3) Unit specifications Nil Unit selection function Note 5) M SI unit only Note 6) Note 5) Since the unit for Japan is fixed to SI due to new measurement law, this option is for overseas
D Auto identification function Display units can be selected using either or . This function automatically identifies the pressure range of the pressure sensor that is connected to the multi-channel pressure sensor controller, thus eliminating the need of having to reset the range again after replacing the sensor.
Series HRS100/150 CAT.NAS40-62B R410A as refrigerant Thermo-chiller Standard Type Series HRS100/150 Circulating Fluid Temperature Controller Triple controller Fan Air-cooled condenser fan control Cooling valve Heating valve Circuit diagram Ventilation Cooling valve control Fan Facility water outlet Temperature sensor (Heat exchanger inlet) Water-cooled condenser Dryer Air-cooled condenser D
The valve arrangement is numbered as the 1st station from D side. Under the manifold base part number, state the valves to be mounted in order from the 1st station as shown in the figure above. Refer to page 1520 for manifold options. 1519 VFA3000/5000 Series Manifold Options For base mounted Blanking plate assembly Mounting screw, gasket part no.
Nil S n No Perpendicular to axis D With auto switch (Built-in magnet) Nil For a cylinder with D, -B is suffixed to the end of the part number. Auto switch Axial R Nil Without auto switch For applicable auto switches, refer to the Applicable Auto Switch.
How to Order VFN212 02 N 5 F D Z CE marking NAMUR Interface Nil Q CE marked product Voltage Thread type 1 100 VAC, 50/60 Hz 2 200 VAC, 50/60 Hz 3 110 to 120 VAC, 50/60 Hz 4 220 VAC, 50/60 Hz 5 24 VDC 6 12 VDC 7 240 VAC, 50/60 Hz Nil Rc (PT) F G (PF) N NPT Electrical entry Solenoid G Grommet E Grommet terminal T Conduit terminal D DIN terminal Nil Single solenoid D Double solenoid Manual
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 1/8, I.D. d(inch): 0.086, Tube O.D.
inch): 3/16, I.D. d(inch): 1/8, Tube O.D.