Air cylinder (Series compatible with secondary batteries) Description Qty 1 Rod cover 1 2 Head cover 1 3 Cylinder tube 1 4 Piston rod 1 5 Piston 1 6 Cushion ring 1 7 Cushion ring B 1 8 Bushing 1 9 Cushion valve 2 10 Tie-rod 4 11 Retaining ring 2 12 Spring washer 8 13 Tie-rod nut 8 14 Wear ring 1 15 Cushion seal 2 16 Rod seal 1 17 Piston seal 1 18 Cushion valve seal 2 19 Cylinder tube gasket 2 20 Piston gasket 1 21 Rod end nut 1 22 Magnet (1) 25
Selection Step 1. Pad selection 1-A Theoretical lifting force 1-B Calculation method: Pad diameter 2.
This prevents the accumulation of oil inside the pilot valve. 7. Piping to products When piping to a product, avoid mistakes regarding the supply port, etc. Air Supply Wiring 1. Type of fluids Please consult with SMC when using the product in Warning Warning 1. The solenoid valve is an electrical product.
8 16.5 6 11.5 25 9.5 depth 5.4 53 45 8 14 12 M10 x 1.5 12 6 36 5.5 49 1/8 17 8 12 32 11 depth 6.5 66 56 10 18 14 M12 x 1.75 15 7 47 6.6 63 1/4 19.5 10 19.5 40 14 depth 8.6 75 65 10 22.4 19 M16 x 2 20 7 52 9 71 1/4 21.5 10 21.5 50 17.5 depth 10.8 81 70 11 28 24 M20 x 2.5 24 8 58 11 81 1/4 24 10 24 63 20 depth13 90 77 13 35.5 30 M27 x 3 33 9 69 13 100 1/4 27.5 10 27.5 80 23 depth 15.2 105 88
Wiring 1) Insert cable gland (4), washer (5) and rubber seal (6) into cable In the case of indicator light assembly DC Terminal no.1 (+) (7) in order, and insert it into housing (2). Coil 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Terminal no.2 (-) Note 1) The tightening torque should be 0.5 Nm +/15%.
0.7 M5 x 0.8 M6 x 1 M8 x 1.25 488
4 3/8 1/4 3/8 Rc, NPT 1/8 1/4 3/8 Rated voltage Note 5) 100/110/200/220/230/240/24/48VAC 12/24VDC Ambient and fluid temperature oC 5to60 Power consumption [W] Note 6) DC polar indication 4.5 7 10.5 Apparent power value [VA] Note 6) AC 7 9.5 12 DC polar indication 50 55 65 Temperature increase of the coil [oC] Note 7) AC 60 70 70 Allowable voltage fluctuation 10% of the rated voltage or less
AMX-OMZ0094 PRODUCT NAME Micro Mist Separator MODEL / Series / Product Number AMD50-(F,N)06 ~ (F,N)10(B,C,D)(-J,L,R,W,Z)-D AMD60-(F,N)10(B,C,D)(-J,L,R,W,Z)-D Contents Page 1. Safety Instructions 2 to 6 2. Application 7 3. Standard specifications 7 4. How to Order 8 5. Construction / Options / Replacement parts 9 6. Bowl assembly specifications 10 to 11 6-1.
(Pairing) Red/green 24 V (Control and input) 24 V (Control and input) 1 1 FRANCE (33) 1 6476 1000 Orange LED is ON.
Mount the tube gasket 9 to the right cover 2 to mount to the body 1 . Tighten them with the hexagon socket head cap screw with washers 12 . 17 15 3 10 14 26 11 5 12 19 9 12 14 1 11 26 4 2 6 15 Cushion seal 4 Direction of the shaft(key) 38 - 7. Mount the pipe 21 to the sub-plate 18 19 and 30 and fix with hexagon socket head cap screws 22 31 to the body 1 . 8.
Wiring 1) Pass cable (8) through cable gland (5), plain washer (6), and rubber seal (7) in that order, and then insert into the cover (4). 2) As shown below, strip the outer layer of cable (8) and crimp the crimped terminal (9) on to the ends. Note) Wire the power leads of the cable to No.1 and 2 terminals.
Caution 1. Drain flushing Remove drainage from the air filters regularly. 2. Lubrication Once lubrication has been started, it must be continued. Use class 1 turbine oil (with no additives), VG32. If other lubricant oil is used, it may cause a malfunction. 7 VT315-OMH0002-D VT315 Series 3 port solenoid valve Specific Product Precautions (1) Be sure to read this before handling.
AMX-OMZ0093 PRODUCT NAME Mist Separator MODEL / Series / Product Number AM50-(F,N)06 ~ (F,N)10(B,C,D)(-J,L,R,W,Z)-D AM60-(F,N)10(B,C,D)(-J,L,R,W,Z)-D Contents Page 1. Safety Instructions 2 to 6 2. Application 7 3. Standard specifications 7 4. How to Order 8 5. Construction / Options / Replacement parts 9 6. Bowl assembly specifications 10 to 11 6-1. Bowl assembly for AM50 10 6-2.
/8 (Rc, NPT, G) OUT port L-bracket 27 12 27 24 24 1.6 15 25 7 10 2.3 (8.5) 33 45 50 5 Series ITVX2000 Specific Product Precautions 1 Be sure to read before handling.
Assembly 1) Insert cable gland (4), washer (5) and rubber seal (6) and housing (2) into cable (7) in order. Connect cable (7) to terminal block (3) and fix terminal block (3) to housing (2) in place.
Use class 1 turbine oil (with no additives), VG32. If other lubricant oil is used, it may cause a malfunction. 7.
Roll moment Mr(Nm) 1 N m = 0.7375 ft lb 31 MXH Series Compact Slide Construction MXH6 (6) MXH10 (10) 20 6 21 17 2 1 19 5 18 8 10 20 6 21 16 2 1 19 5 18 10 8 3 24 13 9 7 22 14 4 11 15 12 3 24 13 23 22 7 4 11 MXH16, 20 (16, 20) 20 6 21 17 2 1 19 5 18 18 8 10 4 7 22 23 13 24 3 12 11 Parts list Parts list Description Material Note Description Material No.
0.001 MPa DC1224 V(pp) 10() 55 mA() [] -1.5 V 40 mA(4100 mA) 2 DC15 V(800 k) 4 (26.4 V) 3 3 digits NPNPNP 5(CH12CH2CH41) 80 mA DC30 V(NPN) 1 V(80 mA) 5 ms 20160640 ms 0.1F.S. 1 digit (25 ) 0.5F.S. 1 digit 4 7() 1 7() ON() ()10 msON/OFF IP65()IP40 050 -1060 () 3585RH() AC1000 V1 50 M(DC500 V) 0.5F.S.(25 ) 8Pe-con CERoHS 8 4.8 2 m 0.15 mm 2 0.9 mm PBTCR
Test piece posture : lateral Vacuum Pump Endurance test conditions Valve side Valve side Bellows side Bellows side Chamber Vacuum pump Vacuum pump Chamber Recommended direction of exhaust Recommended direction of exhaust 9 XM-OMP0005-A 7. Parts replacement procedure 7-1. Precautions Be sure to follow [1. Precautions 1] when disassembling the product for maintenance.
Byte0: Station Status 1 Bit 7 0 0 0 0 0 X 0 0 0 Diag. Station_Non_Existent 1 when SI unit is not recognized by the master Diag. Master_Lock 1 when SI unit is set as the other master Diag. Prm_Fault 1 when the parameter regarding the SI unit is wrong Diag. Station_Not_Ready 1 when the SI unit is not ready for data transmission Diag.